Taper Line, Inc.
Taper Line, Inc.
23426 Reynolds Court Clinton Twp., Michigan 48036
Emergency: (586) 995-1263 • (586) 549-5533
Phone: (586) 775-5960
Fax: (586) 775-6990 • (586) 468-3052
Email: taper@taperline.com Website: www.taperline.com
Print Back
Face1.jpg
Unit of Measure
Items Face1.jpg
TLN-03
0.664-32 Face Lock Style, Inch Bearing Locknut 		Face1.jpg
TLN-04
0.781-32 Face Lock Style, Inch Bearing Locknut 		Face1.jpg
TLN-05
0.969-32 Face Lock Style, Inch Bearing Locknut 		Face1.jpg
TLN-06
1.173-18 Face Lock Style, Inch Bearing Locknut 		Face1.jpg
TLN-065
1.312-18 Face Lock Style, Inch Bearing Locknut
Description N/A
Bearing Bore Number N/A 03 N/A 04 N/A 05 N/A 06 N/A 065
Diameter (A) N/A 1.125 in N/A 1.375 in N/A 1.562 in N/A 1.750 in N/A 2.062 in
Dimension (B) N/A 0.343 in N/A 0.375 in N/A 0.406 in N/A 0.406 in N/A 0.438 in
Diameter (C) N/A .938 in N/A 1.125 in N/A 1.281 in N/A 1.500 in N/A 1.813 in
Hole Slot/Diameter (D) N/A .125 in N/A .188 in N/A .188 in N/A .188 in N/A .188 in
Dimension (E) N/A .094 in
Dimension (F) N/A .664 in N/A .781 in N/A .969 in N/A 1.173 in N/A 1.312 in
Pitch Diameter (G) N/A .6437 in.6467 in N/A .7607 in.7641 in N/A .9487 in.9521 in N/A 1.1369 in1.1409 in N/A 1.2764 in1.2804 in
Pitch - Threads Per Inch (H) N/A 32 N/A 32 N/A 32 N/A 18 N/A 18
Pilot Diameter (J) N/A .6695 in.6699 in N/A .7876 in.7880 in N/A .9845 in.9849 in N/A 1.1813 in1.1817 in N/A 1.3145 in1.3150 in
Dimension (K) N/A .156 in
Face Lock Screw Size N/A
Face Lock Screw Thread Type N/A
Minimum Face Lock Torque Value N/A 2 to 3 ft·lb N/A 2 to 3 ft·lb N/A 2 to 3 ft·lb N/A 2 to 3 ft·lb N/A 3 to 4 ft·lb
Screw Size N/A 10 N/A 10 N/A 10 N/A 10 N/A 1/4 in
Style N/A Face Lock Style
Class N/A Class 3B Thread
Intended Application N/A Bearings
Fastener Type N/A Locknut
Materials N/A Carbon Steel
Note N/A
  1. Also available in left hand threads.
  2. All locking screws should be tightened equally to a maximum torque. Conditions may vary from the actual torque figures, however, listed values are minimums.
  3. All parts complete with locking screws.
  4. It is not necessary to use any type of locking fluid on the set screws. At no time should TAPERLINE(R) products be altered. The manufacturer shall not be held accountable for any product that has been altered.
  5. All items listed are low carbon steel. They can also be furnished in stainless steel or alloy steel, at additional cost.
  6. In the smaller thread sizes holding power of the face lock feature has its limitations. As thread size increases, holding power increases. TAPERLINE(R) recommends the use of the peripheral lock feature when applicable in the smaller sizes. Check your application for your torque requirements.
Piloted Locknuts assure concentricity of nut to shaft in high speed applications
Use suffix "P" - for Piloting Feature (Extra Cost)
Locknuts are furnished with both Spanner Slot & Holes.
Face Lock Screws may extend beyond locking face.
Available on CAD Library

NOTE: Dimensions apply to both Face & Peripheral styles. Locknuts are checked on "GO" size gauges.