Taper Line, Inc.
Taper Line, Inc.
23426 Reynolds Court Clinton Twp., Michigan 48036
Emergency: (586) 995-1263 • (586) 549-5533
Phone: (586) 775-5960
Fax: (586) 775-6990 • (586) 468-3052
Email: taper@taperline.com Website: www.taperline.com
Print Back
PH2.jpg
Unit of Measure
Items PH2.jpg
TLN-00-PH
0.391-32 Peripheral Lock Style, Inch Bearing Locknut 		PH2.jpg
TLN-01-PH
0.469-32 Peripheral Lock Style, Inch Bearing Locknut 		PH2.jpg
TLN-02-PH
0.586-32 Peripheral Lock Style, Inch Bearing Locknut 		PH2.jpg
TLN-03-PH
0.664-32 Peripheral Lock Style, Inch Bearing Locknut 		PH2.jpg
TLN-04-PH
0.781-32 Peripheral Lock Style, Inch Bearing Locknut
Description N/A
Bearing Bore Number N/A 00 N/A 01 N/A 02 N/A 03 N/A 04
Diameter (A) N/A .875 in N/A 1.000 in N/A 1.125 in N/A 1.125 in N/A 1.375 in
Dimension (B) N/A 0.312 in N/A 0.312 in N/A 0.343 in N/A 0.343 in N/A 0.375 in
Diameter (C) N/A .625 in N/A .719 in N/A .813 in N/A .938 in N/A 1.125 in
Hole Slot/Diameter (D) N/A .125 in N/A .125 in N/A .125 in N/A .125 in N/A .188 in
Dimension (E) N/A .120 in N/A .094 in N/A .094 in N/A .094 in N/A .094 in
Dimension (F) N/A .391 in N/A .469 in N/A .586 in N/A .664 in N/A .781 in
Pitch Diameter (G) N/A .3707 in.3733 in N/A .4487 in.4513 in N/A .5657 in.5687 in N/A .6437 in.6467 in N/A .7607 in.7641 in
Pitch - Threads Per Inch (H) N/A 32
Pilot Diameter (J) N/A N/A N/A .5908 in.5912 in N/A .6695 in.6699 in N/A .7876 in.7880 in
Dimension (K) N/A N/A N/A .156 in N/A .156 in N/A .156 in
Minimum Peripheral Torque Value N/A 2 ft·lb
Screw Size N/A 10
Style N/A Peripheral Lock Style
Class N/A Class 3B Thread
Intended Application N/A Bearings
Fastener Type N/A Locknut
Materials N/A Carbon Steel
Note N/A
  1. Also available in left hand threads.
  2. All locking screws should be tightened equally to a maximum torque. Conditions may vary from the actual torque figures, however, listed values are minimums.
  3. All parts complete with locking screws.
  4. It is not necessary to use any type of locking fluid on the set screws. At no time should TAPERLINE(R) products be altered. The manufacturer shall not be held accountable for any product that has been altered.
  5. All items listed are low carbon steel. They can also be furnished in stainless steel or alloy steel, at additional cost.
  6. In the smaller thread sizes holding power of the face lock feature has its limitations. As thread size increases, holding power increases. TAPERLINE(R) recommends the use of the peripheral lock feature when applicable in the smaller sizes. Check your application for your torque requirements.
Piloted Locknuts assure concentricity of nut to shaft in high speed applications
Use suffix "P" - for Piloting Feature (Extra Cost)
Locknuts are furnished with both Spanner Slot & Holes.
Face Lock Screws may extend beyond locking face.
Available on CAD Library

NOTE: Dimensions apply to both Face & Peripheral styles. Locknuts are checked on "GO" size gauges.